Kenwood CT-405 Manual de usuario

KXF-W4030CT-405STEREO CASSETTE TAPE DECKB60-4536-08 (EN)KENWOOD CORPORATIONINSTRUCTION MANUAL

10Playback (recording) preparation2Select the tape transport direction.1Load a cassette tape in deck A or B.Preparation for playback (recording)Before

11Listening to cassette tapeNormal playbackListening to cassette tapesPreparationMake “Playback (recording) preparation”.0Zero-stop operationTo play s

12Listening to cassette tape÷Tapes are played in the directions indicated by their respective indica-tors on the display.÷The playback starts with the

13

14Convenient music search (DPSS)Skip play operationTo play the tune located 4 tunes behindConvenient music search (DPSS)The DPSS (Direct Program Searc

15Convenient music search (DPSS)Single-tune repeated playback operation÷Normal playback resumes after repeating the same tune for 16 times.÷Press t

16How to record (Deck B only)Each press of the MODE key changes the setting.1 “LEVEL” lights up: Recording level setting mode2 “BAL.” lights up: Recor

17How to record (Deck B only)÷Recording will start.÷The deck enters the stop mode automatically when the tape hasbeen recorded till the end.Press once

18How to record (Deck B only)To stop recordingIn stop modeDuring recordingPauseTo pause recording temporarilyHow to provide non-recorded blanks betwee

19Perform auto-bias adjustment. (The bias adjustment is applied to deck B.)Tape dubbing operation (Deck A \ Deck B)To stop dubbingPress the stop (7) k

2Introduction*AC voltage selectionThe AC voltage selector switch on the rear panel is set to thevoltage that prevails in the area to which the unit is

20Start playing the CD.Set the record-pause mode.Adjust the recording level.2Press 7 key of theCD player.Press the 6 keyof the CD player.1 Play a CD.

21Recording of CD playback (CCRS) (Deck B only)1Insert a tape in deck B.2Determine the recording condition.1Select the recording mode.3When connected

22÷Set the timer so that the tape starts at the desired time of the day.÷When the set time comes, tape playback starts automatically.÷Read carefully t

2334Set the TIMER switch to REC.Set the amplifier volume to the minimum position.÷Refer to the "How to use the MPX FILTER key". &÷To can

24In case of difficulty÷Please note that resetting microcomputer clears contentsstored inand returns it to the condition when it left the factory.What

In case of difficulty25÷Use a cassette with unbroken tab or close thehole.÷Close the cassette holder completely.÷Adjust the recording level referring

26Dolby noise reduction systemThe Dolby noise reduction system was developed to reduce the tape hiss noise generated during playback.The optimum effec

27Track System ... 4 track, 2 channel stereoRecording System ... AC bias (Frequency: 105 kHz)Heads ...

For your recordsRecord the serial number, found on the back of the unit, in the spacesdesignated on the warranty card, and in the space provided below

3AccessoriesCheck that the following accessories are present.Audio cord ... (2) System control cord ... (1)AC plug adapt

4Caution on condensationCondensation (of dew) may occur inside the unit when there is a greatdifference in temperature between this unit and the outsi

5To store cassette tapesDo not store the tapes in a place which is subject to directsunlight, or near equipment that generates heat. Keep thecassette

6LINE INREC PLAYLINE OUTSYSTEM CONTROLLR1234567890 +100764¢1¡PHONOTAPEREC PLAYLRSIGNAL GNDRLSYSTEMCONTROLSYSTEMCONTROL1. Connect all cords firmly.

7SYSTEM CONTROL OPERATIONSRemote ControlLets you operate this unit with the system remote control unit supplied with the amplifier or receiver.Automat

8TAPE AAUTO REVERSETAPE BAUTO REVERSEPOWERPHONESTIMER PLAYREC OFF PLAYMODEREC LEVEL/BAL/BIAS- ON – OFF1237¡ 1 ¡8PAUSE ¶REC/ARM0237RESET AMIN/L MAX

91 Deck AThis deck is used exclusively for play-back.2 Deck A eject (0) key 0Press to open the cassette holder ofdeck A.3 Deck B eject (0) key 0Press